Differences

This shows you the differences between two versions of the page.

--- hardware:room-case-2.0 [2025/05/31 22:45] – jtbx
+++ hardware:room-case-2.0 [2025/06/01 15:54] (current) – jtbx
@@ Line 4: / Line 4: @@
 See [[projects:case_2.0|]] for motivation and design decisions.
-Each room setup now consist of two [[https://www.amptown-cases.de/en/product/transflex/|TRANSflex]] road cases with rack modules for key components.
+Each room setup now consist of two [[https://www.amptown-cases.de/en/product/transflex/|TRANSflex]] road cases with rack modules for key components. {{ :hardware:voc-case2_0-pallet-comp.jpeg?400|}}
 Both road cases fit on a euro pallet when tipped on their short side.
 So during transport each lecture room will occupy 120x80 cm (height approx. 140 cm) and during operation 2x 120x60cm are needed (height approx. 80cm).
-TODO: Image of pallet
+<WRAP clear></WRAP>
 ===== Usage =====
 TODO: Revise signal diagram and add buildup instructions: {{projects:case2-hall-cabling.png}}
+==== Case A ====
+Contains the modules as well as the camera, mixer laptop, microphones and TODO.
+TODO: Picture
+<WRAP clear></WRAP>
+==== Case B ====
+{{ :hardware:voc-case2_0-case_b-comp.jpeg?300|}}
+Contains accessories like:
+  - tripod
+  - cable mats
+  - etc.
+<WRAP clear></WRAP>
 ===== Assembly =====
 ==== FOH Module ====
+{{:hardware:voc-case2_0-foh-front-comp.jpeg?400| }} {{:hardware:voc-case2_0-foh-back-comp.jpeg?400|}}
-TODO: Add images of front and back
 Custom builds:
@@ Line 44: / Line 58: @@
 ==== Lectern Module ====
+{{:hardware:voc-case2_0-lectern-final-comp.jpeg?400| }}
-TODO: Add pictures
 Custom builds:
@@ Line 67: / Line 80: @@
       * 0.5m HDMI from ATEM Mini Output to HDMI splitter
       * 0.5m HDMI from HDMI splitter to Up-Down-Cross
-    - Connect cables running from drawer to I/O panel and dress them into a wire harness
+    - Connect cables running from drawer to I/O panel and dress them into a wire harness {{ :hardware:voc-case2_0-lectern-assembly-drawer.jpeg?200|}}
       * 3x 1.5m HDMI to ATEM inputs 1-3
       * 1x 1.5m HDMI from HDMI splitter
@@ Line 76: / Line 89: @@
       * TODO: Power (don't connect to power supply yet)
     - Connect wire harness to I/O d-norm panel (but don't connect ethernet to the switch yet)
-  * //Now you'll have two parts: The drawer connected to the I/O panel with HDMI, SDI and audio as well as the rack tray with the ethernet switch//
+  * //Now you'll have two parts: The drawer connected to the I/O panel with HDMI, SDI and audio as well as the rack tray with the ethernet switch// {{ :hardware:voc-case2_0-lectern-assembly-parts.jpeg?200|}}
   * Assembly:
     - Adjust the length of the rack drawer rails and mount them in the top rack unit
@@ Line 91: / Line 104: @@
       * connect the 3 ethernet cables to their respective sockets
       * screw down I/O panel
+{{:hardware:voc-case2_0-lectern-assembly-io.jpeg?200|}}
+{{:hardware:voc-case2_0-lectern-assembly-mount.jpeg?200|}}